Re-Rx7's Sterling Grey 11'
 

Never posted any pics of my ride. So i figured I woud given the fact I just bought Dark Pony's wheels. Almost done, just need GT500 spoiler, Pro kits and a front lip.

This is with the 305 DR's.
http://i44.photobucket.com/albums/f3...ps19754e77.jpg

This is with the Bridgestone 285-35 RE070r's. Same as GTR uses. HAd to replace one of the DR's. Dark Pony HAd a flat and the inside of the sidewall was paper thin from rim rubbing it.

http://i44.photobucket.com/albums/f3...psnbnwqil6.jpg

http://i44.photobucket.com/albums/f3...psfsmhsmdd.jpg

So you're the bastard that bought them before me!

Looks good!

It is I. The BAstard!:rockit:

Looks good man! Any close up pics of how the 305/35-20s fit? Looking at putting some Nittos on a 10" wheel, trying to decide whether to go 305 or 315 since they run so narrow.

I may have one pic. I have a set of 305's nittos cheap if your interested. One is brand new other 50%. They tuck even with the rear fender. I was worried about it as well.

Awesome man I apprectiate it. And no I would think about it but I won't be back in the country for another 6 months or so. Needs more low! What lowering kit are you gonna go with?

Eiback Pro kits probally. I don't like the slammed look. Plus Im tryna keep a lil ride quality.

Nice man. Is your car registered in OK so you avoid the front plate law?

-Alex

Looks...familiar...lol

Yea it kinda does? Weird. :hmmm2:

Gt500 spoiler installed. Pia!!
http://i44.photobucket.com/albums/f3...pspom97szz.jpg
http://i44.photobucket.com/albums/f3...pstwgjgocb.jpg

Pia? Lol it took me 5 mins

5min to get the old spoiler off the car?

Glad to see I am not the only one that went through that task this weekend. Looks good.

-Alex

The pain is getting the stocker off.

It was a pita for me. Ripped some paint off of my trunk too :/ No spoiler ftw.

Tell me about it. Thanks Alex.

Yup lol not bad if you have a heat gun

You did it wrong then.

I just used plenty of Goo Gone.

-Alex

A little Goo Gone, a little heat gun and a little 50 pound test braided fishing line (with 2 sticks on the ends, used like a saw) and they come off quite easy. Also helps to do it on a hot Texas summer day.

I did it in the 29 degree wind blowin out of the north at 30mph weather. Like a boss.

Did you use double-sided tape on the new spoiler?

-Alex

Yes, 3m. Followed the same outline that it came off with.

Might want to go over it with a hair dryer at some point. I can't be sure but, I was told that the tape needs to be warm to properly adhere. I have not tried to prove this on my car by removing the screws and pulling on it.

-Alex

I believe pressure is a more important factor then temp. I usually put C clamps on them for an hr so before removing.

I have 315 NT05 on a 20x10 and they fit well. i've had no issues with them.

Pic please?^^

Clean shot after wash.
http://i44.photobucket.com/albums/f3...psqmimsb1n.jpg

Lowered on FRPP K springs, GT/CS facia added oh and gt500 mudflaps!! Whoo! Car is coming along nicely.

http://i44.photobucket.com/albums/f3...psofojdkz7.jpg

http://i44.photobucket.com/albums/f3...psrq6qampa.jpg

http://i44.photobucket.com/albums/f3...ps6xwewkio.jpg

Looks good man. You plan on keeping the factory grill?

-Alex

I like it. I'm torn between it and a boss 302s grille. 300$ is a lot for a grille though.

Gotcha.

-Alex

Anybody know if the GT500 spoiler will cover the four forward holes left by the GT/CS?

Right now I have them covered, but I'd like to do it better.

It won't.

Looks good man. Those are some wide ass 285s!

Lol yea they are 285's though. I get told that alot, they are Bridgestone re070r's 285/35

New car cover. Oem.
http://i44.photobucket.com/albums/f3...psh6prp20y.jpg

http://i44.photobucket.com/albums/f3...psgqxon5mz.jpg

Perfect timing for that, with the crazy weather. I need to pick one up for mine when it has to stay outside...

I got it for free 99. Yea man glad I have it after today.

You did not like running the 305's on it?