continued from above
This was our last autocross planned for the year. We have lots to work on over the winter to this car, mainly turning it into a more track-worthy car, with the compromises of running "autocross and track and street" down to just "track and street only", as the 2013 GT is getting closer to ESP set-up. We have another set of coilovers on hand for the '13 (AST 4200RR), as well as a Watts Link kit (Whiteline, of course), and some other bits and pieces that we will show in that build thread (I will link it from here when I start it).
Preparation for Five Star Ford track day
So that was two weeks ago and today we're prepping the 2011 GT for another track event. This is an informal HPDE put on by the Five Star Ford of Plano dealership where we got our '13 GT, and the dealer we got that car from is setting this up (Corey White). This is the same group that did this back in June. Weather for tomorrow looks nice and we should have 40-50 cars. Amy will be driving the '11 GT and Matt will be in his BRZ (which got 255 Hankook R-S3s on the 17x9" wheels, Carbotech brake pads, and an oil change today, too).
One of the biggest changes to the '11 GT was a height reduction on the rear wing element. After hearing from several aero experts about the poor placement of our APR 3D wing element ("it doesn't work above the roofline!") we finally got around to shortening our custom built wing uprights. Ryan took 5 inches out of the height and the element now sits below the roof line.
Ryan, and our new tech that started this week Olof, got the Mustang and BRZ cleaned up, inspected, tires swapped, brake pads swapped, and the red car is being loaded into the trailer now. We will be out at Eagles Canyon bright and early tomorrow morning to put in some solid laps in both cars.
The differential in the 2011 GT is fried again, so we'll order another carbon clutch pack rebuild kit from Ford and get that installed in the coming weeks. The left rear outer axle seal is weeping a tiny bit of fluid, so that needs to be changed. The next event for this car is another ECR track event December 8th - the annual "Toy Run" event.
2012 Mustang Boss 302-S Prep
During the week of Nov 5-9th we worked on American Iron racer Mark Smith's
Boss 302-S race car here at Vorshlag. Figured I'd show this car, as it has some pretty cool parts and capabilities as delivered from Ford. I will show more on this car in a future post, too.
After setting a track record at ECR in October, he brought the car to Vorshlag for some more tweaks, updates, and repairs. We had discussed some weight saving items we could tackle for a good 75+ pound drop in weight. American Iron runs with a power:weight formula, and the 302-S can run a variety of restrictors to go up and down in power. With a lower weight he can run less power, then add ballast to use a larger restrictor for more power at bigger tracks. Flexibility...
The big update we made was a new custom mandrel bent exhaust, to replace the nearly stock parts that these cars come with. We left the stock exhaust manifolds in place, as much as it pained me, and concentrated on a lightweight, high flow race exhaust that included 16 gauge Stainless Steel mandrel bends, two 4" round Magnaflow stainless mufflers, and a custom X-merge, all made in-house here by our fab guru Ryan. The new system stopped just below the rear axle and the car dropped about 45 pounds - and picked up a lot of power.
The entire system is tucked above the bottom of the frame rails and shouldn't ever scrape anywhere, unless it runs over something off track that only hits under the middle of the car. Ryan added heat shielding to the tunnel near the tips, built custom hangers with poly mount bushings, and it looks and sounds amazing.
With the stock air filter/box in place and the stock exhaust manifolds, power jumped from 365 to 420 whp! The old number had a home-brew air restrictor in place, which was changed for a proper restrictor in the throttle body. LG Motorsports dyno'd the car with three different size restrictors and now it has 365 whp again, but a lot more torque than before. He can also run the car at three different weights now and has the dyno charts and restrictors needed for each AI legal set-up.
Ryan built a custom bracket for this sub-3 pound battery Mark wanted to try - and the dang thing works! It charges fast and will start the car at least 5 times in a row with the same charge. Dropped 30 more pounds with this battery, and the old one can be swapped in quickly to add ballast or if the new wiz-bang battery craps out. New front wheel bearings, a strut repair, lots of clean-up work, new fluids in the diff/cool and trans/cooler, and a sound test rounded out our work for the week. Mark was very pleased with the car, the exhaust still managed to only blow 95 dB, and he did well at two races at NOLA last weekend.
Video of the drive-by in the 302-S with a sound meter at 50 feet.
A rear main seal leak (that we warned him about) became worse in those two races at NOLA and a slipping clutch ended his weekend early, after the second race. He managed to secure 2nd overall in AI for the year for NASA Texas, so he was happy with that (he only ran about half of the races). Next year - look out! I suspect Mark's 302-S will likely win even more AI races.
Anyway... this quick post grew a bit! I better sign off and help get the trailer loaded. Until next time!