Terminators For the whiners that want their own section :) |
Sponsored Ads |
|
Welcome to DFW50s.com
|
Register to remove these ads.
02-08-2013, 01:21 PM
|
#1
|
Senior Member
Join Date: Jun 2012
Location: DFW
Posts: 638
|
Your Setup
Lets get a What you are running Thread going:
2.8 KB with 3.1 pulley, stock lower
Still Returnless, E85, Division X rails, 80lb injectors, dual FPDMS, GT Pumps, BAP, Fore Hat, tuned by 04Sleeper
Basic Boltons: Division X Idlers, JLT Intake
Making 720hp/689tq
What you got?
|
|
|
02-08-2013, 03:19 PM
|
#2
|
Senior Member
Join Date: Jul 2012
Location: South Grand Prairie
Posts: 277
|
Basics
3.3L Lysholm, 3.5" pulley, stock lower, custom blower cams, Fox Lake Stage III heads. 21psi
Kooks 1-7/8" long tubes, off road x, 3" MAC catback
Return style, E85, Lysholm rails, 105lb injectors, 3x Walbro GSS342 pumps, Fore hat, BAP
Division X idlers, Vortech 5" intake and wide mouth throttle body, gt500 maf, a whole bunch of non performance stuff
817/687
__________________
2004 Cobra
Some mods
|
|
|
02-08-2013, 04:14 PM
|
#3
|
Junior Member
Join Date: Nov 2012
Location: dallas
Posts: 15
|
2.2 kb. 2.76 upper stock lower
Jlt next gen intake
80s , kb bap, gt pumps, stock hat , returnless e85
650hp, 540 ft lbs. Hpp tuned.
Gona get 04 sleeper to tune it soon
__________________
|
|
|
02-09-2013, 03:10 PM
|
#4
|
Member
Join Date: Nov 2012
Location: Fort Worth, Tx
Age: 37
Posts: 55
|
Have all the shit just haven't put it on yet.
2.4 Polished KB with 3.5 Pulley
Lethal Performance Budget Return Style Fuel system
60lbs Inj.
BBK LT's / No-Cat BBK X-pipe / Bassani exhaust
JLT Carbon Fiber Intake
Right now with my current set up I'm putting down 460/480
__________________
04 Mystichrome Vert
588 rwhp 510 tq
|
|
|
02-10-2013, 02:51 AM
|
#5
|
Senior Member
Join Date: Jul 2012
Location: North Dallas
Posts: 218
|
2.3L Gen 2 Whipple 3.3'' pulley, 4 Lb Metco Lower
GT pumps, Fore Hat, Dual FPDM, BAP, Tuned to 93
Basic Boltons: Bassani Mids, Bassani X, Bassani CB, BF Idlers, Accufab SBTB, JLT RAI, MGW shifter, STOCK SPRINGS, STOCK REAR(with BF brace) 305 555R DR,
Making ???hp/???tq. Couldn't even tell you the car needs a dyno but it needs a clutch before that sooo. I would venture about 580/535, but again I dont know yet
__________________
- 2003 SVT Cobra : Stock-ish
- 1997 SVT Cobra : Stock
RIP Chris Kyle
|
|
|
02-11-2013, 09:11 PM
|
#6
|
Senior Member
Join Date: Feb 2013
Age: 29
Posts: 246
|
Originally Posted by Eaglei532
2.3L Gen 2 Whipple 3.3'' pulley, 4 Lb Metco Lower
GT pumps, Fore Hat, Dual FPDM, BAP, Tuned to 93
Basic Boltons: Bassani Mids, Bassani X, Bassani CB, BF Idlers, Accufab SBTB, JLT RAI, MGW shifter, STOCK SPRINGS, STOCK REAR(with BF brace) 305 555R DR,
Making ???hp/???tq. Couldn't even tell you the car needs a dyno but it needs a clutch before that sooo. I would venture about 580/535, but again I dont know yet
|
whoops nevermind, I wasn't sure if u got my pm. lol
__________________
Last edited by Stangmaster281; 02-11-2013 at 09:13 PM.
|
|
|
02-11-2013, 10:27 PM
|
#7
|
Junior Member
Join Date: Jul 2012
Posts: 9
|
Stock long block 2.3 TVS 19psi, return style fuel system, ID1000's,E85, kooks 1 5/8 headers,677/606
Tuned by 04sleeper
|
|
|
02-11-2013, 10:52 PM
|
#8
|
I> /\/\
Join Date: Jun 2012
Location: A fender ahead of BlownAltered
Posts: 7,562
|
I know Foofinator's set up is pretty much -
Teksid blocked 302 stroker
ported heads
longtubes
3.08 gears
3.4 Whipple
custom cooler in the trunk
E85 tune
low boost near 800rw
|
|
|
02-12-2013, 06:58 PM
|
#9
|
I have a small penis
Join Date: Nov 2012
Location: Making Steve my bitch since 2003
Age: 44
Posts: 1,465
|
Originally Posted by Steve
I know Foofinator's set up is pretty much -
Teksid blocked 302 stroker
ported heads
longtubes
3.08 gears
3.4 Whipple
custom cooler in the trunk
E85 tune
low boost near 800rw
|
So does he have tubes going through the interior of the car or is it underneath?
|
|
|
06-07-2013, 09:14 AM
|
#10
|
Senior Member
Join Date: Jun 2012
Location: DFW
Posts: 638
|
Your Setup
Small update. Have Kooks Headers, Custom 3" X-pipe (purchased from Emwum Garand, had all ceramic coated black) and 3" Polished Bassani cat back system just about ready to go on.
*waiting for the heat to hit before install so I can watch Eric sweat his balls off
|
|
|
06-07-2013, 09:15 AM
|
#11
|
Senior Member
Join Date: Jun 2012
Location: DFW
Posts: 638
|
Your Setup
Next will be fuel system and more boooooosssssttttt!
|
|
|
06-07-2013, 09:47 AM
|
#12
|
Senior Member
Join Date: Aug 2012
Location: Wylie
Age: 37
Posts: 2,266
|
Are those new tires any good at putting your power down?
__________________
2013 Deep Impact Blue GT Premium
386rwhp/383rwtq
|
|
|
06-07-2013, 12:36 PM
|
#13
|
Senior Member
Join Date: Jun 2012
Location: DFW
Posts: 638
|
Your Setup
Once I heat them up. Yes much better.
|
|
|
06-07-2013, 09:16 PM
|
#14
|
DFW5.0s Preferred Vendor
Join Date: Jan 2013
Location: NRH
Posts: 141
|
2003 Sonic Blue 110k+ miles
Fluidyne Radiator and Gords HE w/ dual fans
Girggs Tubular K-Member and lower front control arms
MM Front and rear coilover kit with bumsteer kit
MM Steering Shaft
Full Length Subframes
IRS bushing and stage 5 axles
McCleod RXT Twin Disc
StopTec Slotted Rotors
Not worth mentioning power mods, its a true slowbra with an Eaton, but it sounds damn good
Plans for a whipple or TVS in a year or two
__________________
'66 Ford Fairlane - '69 SCJ Mach 1 - '03 SB Cobra
|
|
|
08-26-2013, 06:45 PM
|
#15
|
Member
Join Date: Sep 2012
Posts: 37
|
Originally Posted by Bearded Banger
Lets get a What you are running Thread going:
2.8 KB with 3.1 pulley, stock lower
Still Returnless, E85, Division X rails, 80lb injectors, dual FPDMS, GT Pumps, BAP, Fore Hat, tuned by 04Sleeper
Basic Boltons: Division X Idlers, JLT Intake
Making 720hp/689tq
What you got?
|
Your fuel system soon......
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|