| Performance Post anything performance related to your Mustang |
| Sponsored Ads |
|
|
Welcome to DFW50s.com
|
Register to remove these ads.
04-11-2015, 02:39 PM
|
#1
|
|
Junior Member
Join Date: Jan 2015
Location: Keller TX.
Posts: 17
|
JBA Long tube headers
Anybody here have JBA long tubes on their car? I know Kooks and American Racing are probably top shelf but can't afford to drop$1,000 to $1,500 on exhaust. Have considered BBK ceramic coated but would rather have 1 7/8 inch.
Any info greatly appreciated.
|
|
|
|
04-11-2015, 09:12 PM
|
#2
|
|
Member
Join Date: Aug 2013
Location: Trophy Club
Age: 74
Posts: 75
|
Good friend of mine has the Jba and is more than satisfied. I would on the size though. Bigger is not always better. Kooks advised me to go with 1 3/4 Helped with low end grunt of the 5.0. Shaun from AED posted recently ithe SVT forum a very good article on this subject. I couldn't find the article. I'll kep looking.
However, You ought to call JBA and ask their opinion of what size would be best for your set up.
I found the article by Shaun
http://www.svtperformance.com/forums...y-size-is-best
__________________
2013 Boss 302 PW, Recaro, Torsen, AED tune, Airaid CAI, MGW, Hotchkis Springs/LCA, Whiteline Relo, CHE K Member w/Torque Limiters, Griggs Torque Arm Kit, T/A rear girdle, Kenny Brown Pan Hard Bar, Whiteline Tranny Bushing, JPC Linelock, JPC stainless clutch line, MT ET Street Radials (when needed), , 2013 GT500 Quad Axle Backs, Kooks LT 1 3/4, O/R X Pipe, Resonator Delete, JPC Line Lock,JPC Clutch Line.
Last edited by Boss949; 04-11-2015 at 10:41 PM.
|
|
|
|
|
04-12-2015, 11:49 AM
|
#3
|
|
Junior Member
Join Date: Jan 2015
Location: Keller TX.
Posts: 17
|
Thanks, I'm going to call JBA and get their input. Thanks for finding the article, I always believed that bigger is better. After reading Shaun's post I can see that's not always the case.
|
|
|
|
|
04-14-2015, 07:45 PM
|
#4
|
|
Junior Member
Join Date: Jan 2015
Location: Keller TX.
Posts: 17
|
Does anybody have any input on a shop in the Ft. Worth area that will do the install? I do not have the facility at this time.
|
|
|
|
|
04-15-2015, 09:20 PM
|
#5
|
|
Senior Member
Join Date: Jun 2013
Location: Irving / Oklahoma City
Age: 41
Posts: 1,896
|
Originally Posted by Fm58
Does anybody have any input on a shop in the Ft. Worth area that will do the install? I do not have the facility at this time.
|
Might check with Frank (Bacadiesel) on here.
-Alex
__________________
2012 GT Premium Hardtop with XX Transmission
Mods page: http://dfw50s.com/showthread.php?t=3376
Ford Racing . Pypes . BMR . CDC . American Muscle . DDM Tuning . BFG . J&M . Amsoil . MMD. JLT
|
|
|
|
|
04-16-2015, 12:40 AM
|
#6
|
|
Member
Join Date: Apr 2014
Location: Arlington
Age: 39
Posts: 63
|
^This.
__________________
2014 5.0 Race Red 6MT
|
|
|
|
|
04-24-2015, 06:56 PM
|
#7
|
|
Member
Join Date: Aug 2013
Location: Trophy Club
Age: 74
Posts: 75
|
Fm58,
Did you ever get the JBA's?
__________________
2013 Boss 302 PW, Recaro, Torsen, AED tune, Airaid CAI, MGW, Hotchkis Springs/LCA, Whiteline Relo, CHE K Member w/Torque Limiters, Griggs Torque Arm Kit, T/A rear girdle, Kenny Brown Pan Hard Bar, Whiteline Tranny Bushing, JPC Linelock, JPC stainless clutch line, MT ET Street Radials (when needed), , 2013 GT500 Quad Axle Backs, Kooks LT 1 3/4, O/R X Pipe, Resonator Delete, JPC Line Lock,JPC Clutch Line.
|
|
|
|
|
04-25-2015, 01:25 PM
|
#8
|
|
Junior Member
Join Date: Jan 2015
Location: Keller TX.
Posts: 17
|
Yes, ordered them from Stage3 Motorsports, they gave me a great deal. They should arrive Tue.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
Linear Mode
