Go Back   Dallas Fort Worth 5.0 Mustang Club > Sponsors and Vendors > Vorshlag Motorsports


Sponsored Ads
Welcome to DFW50s.com

Register to remove these ads.




 
 
Thread Tools Display Modes
Old 11-02-2013, 01:34 PM   #1
Dan12GT
Senior Member
 
Dan12GT's Avatar
 
Join Date: Jul 2012
Location: Roanoke, Texas
Age: 39
Posts: 818
Default Tranny Bushing Review

Got mine the other day and did the install in about 10-15 mins. The part that took me the longest was getting the car in the air.

My review of the part:

* Definitely stiffened the tyranny up, some noticeable extra vibrations coming through the floor boards but nothing excessive.
* Definite improvement in shift responsiveness.
* Overall it feels solid and more fun to drive.

I highly recommend this part. Also I am completely stock as far as the shifter goes and to be honest right now I think i'll keep it that way. I've done a few high rpms shifts and it feels good no lock-out.

Thank again Vorshlag, a great product indeed!
__________________

Airaid CAI | Borla S-Type Catback | Amsoil 10w30 and MTG Trans. Fluid
382hp 387ft/lb | 1/4: 12.9 @ 112mph
Dan12GT is offline  
Old 11-06-2013, 02:05 AM   #2
emery2483
Senior Member
 
emery2483's Avatar
 
Join Date: Jun 2013
Location: Southlake
Posts: 105
Default

how much was it?
emery2483 is offline  
Old 11-13-2013, 06:24 PM   #3
modernbeat
Member
 
modernbeat's Avatar
 
Join Date: Aug 2013
Age: 54
Posts: 34
Default

Originally Posted by emery2483 View Post
how much was it?
Link to the part: Whiteline Positive Shift Kit for MT82 S197 Mustang [KDT928]


Including tax and shipping in Texas it runs right under $40. You can also pick one up in person at the shop.

Bonus, you get to meet Terry!

__________________
Jason McDaniel at Vorshlag Motorsports
modernbeat is offline  
Old 11-13-2013, 11:24 PM   #4
03MachMe
Senior Member
 
03MachMe's Avatar
 
Join Date: Aug 2012
Location: Wylie
Age: 36
Posts: 2,266
Default

Picked mine up at the shop today. It will be going in this weekend with my other parts
__________________

2013 Deep Impact Blue GT Premium
386rwhp/383rwtq
03MachMe is offline  
Old 11-20-2013, 09:58 AM   #5
46Tbird
Senior Member
 
46Tbird's Avatar
 
Join Date: Jun 2012
Posts: 697
Default

I stopped by on Friday to get one. Terry wasn't there, he was working out at the gym while his crew were at the shop busting ass. The V8 Miata is going to be badass and the Chump C4 is going to be DQ'd!

The bushing works as advertised, but the vibrations in the floorboard at ~2500rpm are gnarly. I've driven solid engine mount cars for years and they don't make the chassis groan like this thing does. I'll probably pull it out for daily duty, it's a bit much for that. But it's cheap, very effective, and since it takes about 5 minutes to install it I'll just toss it in when I know I'll be working it hard. Great mod, especially for the price.
__________________
"If this was like, a thousand years ago, I'd be a Picasso. I'd be one of those dudes that cut his damned ear off."
46Tbird is offline  
Old 11-20-2013, 10:24 AM   #6
DirtyD
Senior Member
 
Join Date: Jun 2012
Posts: 5,594
Default

Originally Posted by 46Tbird View Post
I stopped by on Friday to get one. Terry wasn't there, he was working out at the gym while his crew were at the shop busting ass. The V8 Miata is going to be badass and the Chump C4 is going to be DQ'd!

The bushing works as advertised, but the vibrations in the floorboard at ~2500rpm are gnarly. I've driven solid engine mount cars for years and they don't make the chassis groan like this thing does. I'll probably pull it out for daily duty, it's a bit much for that. But it's cheap, very effective, and since it takes about 5 minutes to install it I'll just toss it in when I know I'll be working it hard. Great mod, especially for the price.
A lot of people figured out that if you cut the center section off the bushing, the floorboard vibrations go away about 95%
DirtyD is offline  
Old 11-20-2013, 10:32 AM   #7
Grandpa
I> /\/\
 
Grandpa's Avatar
 
Join Date: Jun 2012
Location: A fender ahead of BlownAltered
Posts: 7,562
Default

Originally Posted by 46Tbird View Post
I stopped by on Friday to get one. Terry wasn't there, he was working out at the gym while his crew were at the shop busting ass. The V8 Miata is going to be badass and the Chump C4 is going to be DQ'd!

The bushing works as advertised, but the vibrations in the floorboard at ~2500rpm are gnarly. I've driven solid engine mount cars for years and they don't make the chassis groan like this thing does. I'll probably pull it out for daily duty, it's a bit much for that. But it's cheap, very effective, and since it takes about 5 minutes to install it I'll just toss it in when I know I'll be working it hard. Great mod, especially for the price.
Thanks for the review, Danny. I'll skip this mod. If I wanted a vibrating shitbox I would have stayed with foxes. lol.
Grandpa is offline  
Old 11-20-2013, 01:18 PM   #8
GunsUp
Senior Member
 
GunsUp's Avatar
 
Join Date: Oct 2012
Age: 35
Posts: 884
Default

Good review. Thanks for the info Danny
__________________
GunsUp is offline  
Old 11-26-2013, 05:39 PM   #9
Fair
Senior Member
 
Join Date: Nov 2012
Posts: 333
Default

Originally Posted by 46Tbird View Post
I stopped by on Friday to get one. Terry wasn't there, he was working out at the gym while his crew were at the shop busting ass. The V8 Miata is going to be badass and the Chump C4 is going to be DQ'd!
hehe, agree with you on that last bit!

Originally Posted by 46Tbird View Post
The bushing works as advertised, but the vibrations in the floorboard at ~2500rpm are gnarly. I've driven solid engine mount cars for years and they don't make the chassis groan like this thing does. I'll probably pull it out for daily duty, it's a bit much for that. But it's cheap, very effective, and since it takes about 5 minutes to install it I'll just toss it in when I know I'll be working it hard. Great mod, especially for the price.
I'm not sure why some cars/people notice a bad vibration and others don't see this. We've nailed it down to two possible causes:

1. Installing the bushing insert backwards. We've seen it done, and it takes talent, but if you follow the included instructions you can't screw it up. It will go in from the wrong direction but you have to force it in and it doesn't fit right. To install this kit correctly you have to DROP the transmission crossmember, and we think some folks are trying to short cut this step and shove it in from the wrong side.



1. A. Some folks cut the center tip off of the insert to reduce vibrations, but we haven't needed to do this yet. and that piece is a big chunk of the bushing insert.

2. Other parts in the driveline that are already amplifying the NVH. Aluminum 1-piece driveshafts might be a culprit, but I suspect it is aftermarket shifters. Many people use aftermarket short shift kits, which generally replace the body mounted shift bushing (with poly or metal), remove a bushing in the shift arm (going to a solid shaft), and some other parts are made metal - to the point that MOST shifters already add some buzz. Maybe this WL bushing kit added to a few brands of shifters causing "too much?? Don't know, because of the dozen or so we've installed on '11-14 Mustangs, many of which had shifters, we have yet to see one buzz. ???



All I know is that I noticed a tiny bit of added NVH but felt a LOT more connected to the shifter when rowing the gears. Recently we installed some aftermarket "Race" poly motor mounts, too. No massive NVH increase, to me. I drove the car around town recently, and it is generally pretty quiet under 4000 rpms, I could barely detect a vibration. In a typical race weekend I might make a few hundred shifts and I've had no missed gears or issues since adding the Whiteline KDT928 kit + a Steeda rear shift bushing (95A poly), and recently race poly motor mounts. But I still use the stock shifter, and gladly.



Your Results May Vary.
__________________
Terry Fair - Owner at Vorshlag Motorsports - www.vorshlag.com - Plano, TX
Former site sponsor

Last edited by Fair; 11-26-2013 at 05:45 PM.
Fair is offline  
Old 11-26-2013, 06:03 PM   #10
DirtyD
Senior Member
 
Join Date: Jun 2012
Posts: 5,594
Default

So which direction is backwards?

Instruction show to insert the bushing from the front of the cross member (facing the back of the vehicle). I can't insert it the other direction because of my Stiffler's DS loop.
DirtyD is offline  
Old 11-26-2013, 06:05 PM   #11
BERT
I love tube socks
 
BERT's Avatar
 
Join Date: Sep 2013
Location: On Donnie's cock
Posts: 744
Default

Y'all have these in stock now, right?
BERT is offline  
Old 11-26-2013, 06:34 PM   #12
modernbeat
Member
 
modernbeat's Avatar
 
Join Date: Aug 2013
Age: 54
Posts: 34
Default

Originally Posted by DirtyD View Post
So which direction is backwards?

Instruction show to insert the bushing from the front of the cross member (facing the back of the vehicle). I can't insert it the other direction because of my Stiffler's DS loop.
Correct, it is inserted from the front. I suspect that some of these aren't getting inserted all the way and the flange that sticks out then contacts the aluminum crossmember and transmits a LOT of vibrations then. When you insert it make sure it's completely home and it should ONLY touch rubber. If it touches the aluminum crossmember it will vibrate.

Originally Posted by BERT View Post
Y'all have these in stock now, right?
Yes, we still have some in stock.
__________________
Jason McDaniel at Vorshlag Motorsports
modernbeat is offline  
Old 11-26-2013, 06:37 PM   #13
BERT
I love tube socks
 
BERT's Avatar
 
Join Date: Sep 2013
Location: On Donnie's cock
Posts: 744
Default

Originally Posted by modernbeat View Post
Correct, it is inserted from the front. I suspect that some of these aren't getting inserted all the way and the flange that sticks out then contacts the aluminum crossmember and transmits a LOT of vibrations then. When you insert it make sure it's completely home and it should ONLY touch rubber. If it touches the aluminum crossmember it will vibrate.



Yes, we still have some in stock.


Well if y'all still have some in a couple of weeks when i'm in town i'll stop by.
BERT is offline  
Old 11-27-2013, 02:27 PM   #14
46Tbird
Senior Member
 
46Tbird's Avatar
 
Join Date: Jun 2012
Posts: 697
Default

Installed mine from the front. I took the crossmember and trans mount out, then used lube and a vise to make sure the bushing was seated all the way. I verified it wasn't touching the crossmember before installing back in the car. I'm pretty particular about suspension and drivetrain parts being installed correctly.

I'm also a wuss, so it's been too cold for me to get back under it and see what's up. I might trim the whole center piece out like some have to see if that makes a difference. If it does, I'll report back. In the meantime, banging gears like a madman has been fun.

PS - I have some generic poly bushing "shifter bracket" in the car. Otherwise the drivetrain is 100% stock.
__________________
"If this was like, a thousand years ago, I'd be a Picasso. I'd be one of those dudes that cut his damned ear off."
46Tbird is offline  
Old 11-27-2013, 08:47 PM   #15
46Tbird
Senior Member
 
46Tbird's Avatar
 
Join Date: Jun 2012
Posts: 697
Default

Figgered it out.

Took down the trans mount and it was immediately apparent that the lower/wider section of the WL bushing was protruding through far enough to make contact with the crossmember. It was obvious where it was rubbing.

So I grabbed a razor blade and trimmed off the part that protrudes through the trans mount, about 3/8", all the way across. Some people whack off that whole lower section of the bushing, but that seems drastic.

Took it for a spin and NVH-wise I can't even tell anything is different than stock, but high rpm shifts are precise as before. This is how it's supposed to feel.

Pic of the remnant below.
Attached Images
File Type: jpg IMG716.jpg (30.7 KB, 16 views)
__________________
"If this was like, a thousand years ago, I'd be a Picasso. I'd be one of those dudes that cut his damned ear off."
46Tbird is offline  
 

Bookmarks



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump