Go Back   Dallas Fort Worth 5.0 Mustang Club > 5.0 Mustang Forum > General Discussions

General Discussions Discuss anything in general about your 5.0 Mustang that doesn't belong within the other categories here.


Sponsored Ads
Welcome to DFW50s.com

Register to remove these ads.




Reply
 
Thread Tools Display Modes
Old 01-03-2013, 12:53 AM   #1
Midnight11
El Presidente
 
Midnight11's Avatar
 
Join Date: Jun 2012
Location: Always ahead of Steve
Age: 34
Posts: 3,367
Default 2011+ Sticking clutch pedal fix

Took this from another forum. I havent had problems like this but i might try it out since its easy enough

My clutch pedal stuck under high RPM shifts. I fixed it.

You can either buy a new line upgrade, buy a new clutch OR do what Im about to show you...

Warning: If you break shit, crash, die, stab yourself in th eye with pliers or in any way become more ugly than you already are after following this DIY guide... I assume no responsibility and you suck.

Step 1 - Remove top clutch kill switch assembly for cruise control. Twist it

Step 2 - Remove clip and arm off of the left side of the pedal, clutch hydraulic arm. HOW you ask? Remove the clip on the left side, then push clutch slightly in to remove pressure, you will feel when it will move freely. Pull left and twist arm parallel to the marching surface aka ground.

Step 3 - Pull pedal towards you/seat/back of car. All the way until the spring pops out of its white plastic cup/seat

Step 4 - Remove fuckshitard spring from your life, reassemble everything else, and realize that your pedal assembly is now a GT500 clone with no stupid ass "assist spring" holding the pedal down

__________________

2013 Ford Mustang 5.0 6M Brembo 3.73s
HPP TUNED
HP-enough
4-0 vs Steve
Midnight11 is offline   Reply With Quote
Old 01-03-2013, 01:04 AM   #2
DirtyD
Senior Member
 
Join Date: Jun 2012
Posts: 5,594
Default

So the question is...why does it happen to some cars M6 5.0s...and but not a single GT500....
DirtyD is offline   Reply With Quote
Old 01-03-2013, 01:12 AM   #3
Midnight11
El Presidente
 
Midnight11's Avatar
 
Join Date: Jun 2012
Location: Always ahead of Steve
Age: 34
Posts: 3,367
Default

Originally Posted by DirtyD View Post
So the question is...why does it happen to some cars M6 5.0s...and but not a single GT500....
that spring that you take out lol its not on the gt500s
__________________

2013 Ford Mustang 5.0 6M Brembo 3.73s
HPP TUNED
HP-enough
4-0 vs Steve
Midnight11 is offline   Reply With Quote
Old 01-03-2013, 01:00 PM   #4
GunsUp
Senior Member
 
GunsUp's Avatar
 
Join Date: Oct 2012
Age: 36
Posts: 884
Default

My clutch started sticking 2 days ago. I've searched all these threads on svtp with no luck.

Car is waiting to be taken in for service on Monday (The dealership is so backed up with the holidays)

Along with my air bag light being on now this has happened.

Also my car has started "jerking" when I back out of my garage. I thought it might be the traction control but it isn't. When I turn the wheel right or left something catches and pops. Almost like it slipping on ice then catches the cement.
__________________
GunsUp is offline   Reply With Quote
Old 01-03-2013, 02:53 PM   #5
Joey289
Senior Member
 
Join Date: Dec 2012
Posts: 184
Default

Does anyone know why this spring is on the GT's and not the GT500's? After doing this mod, does the clutch pedal feel different?
Joey289 is offline   Reply With Quote
Old 01-03-2013, 03:00 PM   #6
Midnight11
El Presidente
 
Midnight11's Avatar
 
Join Date: Jun 2012
Location: Always ahead of Steve
Age: 34
Posts: 3,367
Default

read that it feels better and the clutch is more firm
__________________

2013 Ford Mustang 5.0 6M Brembo 3.73s
HPP TUNED
HP-enough
4-0 vs Steve
Midnight11 is offline   Reply With Quote
Old 01-03-2013, 03:20 PM   #7
Courtesy Flush
Senior Member
 
Join Date: Aug 2012
Location: Keller, TX
Posts: 613
Default

Originally Posted by Joey289 View Post
Does anyone know why this spring is on the GT's and not the GT500's? After doing this mod, does the clutch pedal feel different?
Look under the dash and compress the clutch a few times. You will see that at a certain point the spring hits what i would call a bind point. You can actually buy the GT500 clutch pedal assembly or just modify yours to be similar to the GT500. As midnight said your clutch engagement will feel firmer without the helper spring.
Courtesy Flush is offline   Reply With Quote
Old 01-03-2013, 04:08 PM   #8
DirtyD
Senior Member
 
Join Date: Jun 2012
Posts: 5,594
Default

Maybe I will do this, and it will help even more with the JHR clutch line AND DOT 3/4 fluid.
DirtyD is offline   Reply With Quote
Old 01-03-2013, 04:16 PM   #9
5PointSlow
Senior Member
 
5PointSlow's Avatar
 
Join Date: Oct 2012
Location: Mustang, Ok
Posts: 259
Default

Originally Posted by DirtyD View Post
Maybe I will do this, and it will help even more with the JHR clutch line AND DOT 3/4 fluid.
I haven't done this but I have tilton TSR-1 fluid 622* boiling point. That and the JHR line combined the clutch feels awesome.
__________________
2015 Comp Orange GT Premium Perfomance Pack

SOLD!
2012 Kona Blue GT Premium
Roush TVS/JLT Big Air
Stainless Works Long Tubes and catted X.
Magnaflow Competition Catback
AED Tuned
***Driver Mod***
10.88@134 on street tires
5PointSlow is offline   Reply With Quote
Old 01-03-2013, 05:47 PM   #10
Joey289
Senior Member
 
Join Date: Dec 2012
Posts: 184
Default

Originally Posted by Midnight11 View Post
read that it feels better and the clutch is more firm
Good reason to do it. It feels like I am pushing air compared to my 65. I have a feeling that after driving this 2013 Mustang, the next time I am in my 65 is going to be pretty jerky at first.
Joey289 is offline   Reply With Quote
Reply

Bookmarks




Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump