Vorshlag 2011 Mustang 5.0 GT - track/autocross/street Project

[Fair]

Project Update Jan 18, 2011: We got a lot accomplished on the Mustang over the past week, including installing the first set of AST 4100s, our first set of Hyperco springs, another set of Vorshlag camber plates, and the 18x9" Enkeis and 265/40/18 Yokohama ADVAN AD08s. Then we had the car aligned again at COBB and got it ready to take to the track for Saturday Jan 15th, where Costas and I ran it at the NASA Instructor clinic. Busy week... let's catch up.

AST 4100 on S197 install gallery = here



Stuart at AST-USA put the valving mojo on this set of 4100s, based on the spring rates we discussed and experience he has on his own S197 with ASTs. We picked them up Wednesday and AJ started the install on by getting the Mustang on the lift. He quickly removed the stock front struts assemblies (these had the Eibach lowering springs + Vorshlag plates - which we left intact) and then started on the rear, so I could make a spring perch adapter for the back.



Normally this AST 4100 S197 set comes with a machined black Nylon rear spring adapter, but they were out of stock and only had this set of shocks on hand from a previous test set. No worries, I got the measurements and machined two spring adapters on the manual lathe. Took me too long but I finally got the 3" OD Nylon cylinder whittled down to size, and they slide over the alignment cups on the rear axle. The AST adjustable ride height platforms fit over the Nylon adapter pieces, and the 2.5" ID x 8" x 200#/in Hyperco springs fit onto those, and slide inside the upper OEM spring alignment stub.



As convenient as the inverted rear single adjustable shocks are to adjust on the current 4100 S197 sets, we're working on a new set-up with AST-USA that will go to a standard arrangement + the body will get shorter; this all will give us more stroke at a lowered ride height. We set-up the ride height at the rear to 15.5", same as with the Eibach Pro lowering springs, for now.



Up front we went with a 60mm x 7" x 450 #/in Hyperco spring and a set of our camber/caster plates + 60mm double row bearing upper perches, all placed on the standard 4100 S197 strut. We set the ride height at 15", same as before. We're also working with AST-USA on a new 4100 strut arrangement that will keep the same stroke but allow a 1" lower ride height up front, as well as a double adjustable that is completely different. Look for several more AST shock designs to be tested on this car throughout 2011.

continued below

[Fair]

continued from above

Once the ASTs were on we mounted up we scheduled an alignment check at COBB Tuning Plano for Thursday. I took the car by there and they were amazed that AJ had eyeballed the caster, camber and toe almost spot on. They just had to tweak the toe and we were done in minutes. The car ended up with -2.8° camber, +7.2° caster, and 3/16" total toe out (that was probably a bit excessive, in hindsight, and we'll bring it in to 0" toe for future track events). The ride quality was exceptional, as always, even with radically more front spring rate. We left the rear rates low on purpose, to hopefully help put power down for auto-x use. We might end up with two different spring rates for track and auto-x use - testing different rates at both types of events will show us more, which we'll share.


(click alignment sheet thumbnail above to see larger version)

When I got back from the alignment the tires and wheels had arrived from Tire Rack, and I only had to get one loose tire mounted to the "Test fit" wheel we had ordered earlier. AJ got those mounted up and they looked good.


Click the wheel and tire pics for larger versions

Friday I dropped off dealer orders around town in the Mustang to hopefully get the silicone mold release off the tires, then drove an hour across town at days end to head to Costas' place - they weren't very scrubbed but oh well, we'd get them good and scrubbed in at the track... right?



Wrong - it rained for the next 24 straight hours. It started raining as soon as I arrived at Costas', and we had to load the car onto his borrowed open trailer in the rain. Since we had a simple "in state" tow of only 4 hours, and we weren't bringing much in the way of gear/tires/spares (1 day event), we just used his buddy's open trailer and Costas' truck to tow down with - instead of hauling out my 38' enclosed gooseneck or his 28' enclosed tag trailer for this simple day at the track. Saves a ton on gas and towing with a little 18' open trailer is a total BREEZE compared to either of our big enclosed rigs. We could have driven the car down, but with so many new parts we didn't want to risk some silly failure sidelining us, and we had to be back in Dallas by 6 pm that day.

So we left DFW at 4 am Saturday morning and got down to San Marcos at 7:45am, unloaded, and were ready for the NASA instructor clinic by 8. It rained the entire way down and all day at Harris Hill Road, plus it was cold as balls. We still had fun, even if we didn't get any meaningful testing/data/video on the Mustang, due to the crappy conditions (standing water in most turns, visibility was poor, and grip was non-existent). Costas was an "instructor trainer" and I was there as an instructor trainee, hoping to get signed off for NASA (which could potentially give me a little flexibility at NASA events to take people for ride-thrus). The event was a blast (event write-up located here; picture gallery here) and we both got some good (soaking wet) track time in the Mustang.



Costas took around his trainees in the first 2 of 3 training scenarios in the car while I rode with "mock students" in their cars during the same tests, trying to point out their driving errors (on purpose), proper lines, etc. In the 3rd scenario I drove a "mock student" (Costas) around at 80% speed in my car to show the proper lines, techniques, etc. It was easy and fun, but just not that exciting due to the severely reduced speeds (rain + training). Luckily, after lunch they let us all loose on the track for a fun session, which ended up being about 35 minutes of quicker lapping in the rain. That session made the day!


The Yokohama AD08s were extremely planted in the wet

The Mustang was a blast to drive, even in the wet. 4th gear around the whole track (3rd just caused wheel spin), and with the AD08s and ASTs the car could seemingly pass anything out there. Lots and lots of fun. Big thanks to Costas for towing the car down, shooting so many pictures (430?!) in the rain, and for signing me off on the instructor deal.


There were no fewer than six 2010-2011 Mustangs at H2R that day

So next up - we've got the first real NASA Texas TT/HPDE/race event in 2 weeks (MSR-Houston), which we plan to attend, but the first Dallas area autocross we can make isn't until Feb 27th. We're looking at everyone's schedule and there's literally 4 autocross groups with events the same weekend as the first NASA event - damn it, why does this happen every year??

Anyway, lots more changes are in store for the Mustang. The splitter we're using is supposed to be available in about 2 weeks, and we have several other (STX legal) aero parts planned during the same time frame. Then headers + exhaust + cold air + tuning.

Stay tuned,

[Fair]

Project Update for Jan 24, 2011: The first NASA Time Trial event we're running in is this weekend at MSR-Houston, so its time to look at TT classing for the Mustang. Of course we had been keeping track of everything in our spreadsheet for this car, but I wanted to share it with everyone, hopefully to help people see how "Easy" it is to class a car with NASA TT. The rules and classing for NASA TT are a bit confusing, some would even say very confusing, but the basic classes go like this (from slowest to fastest): TTF -> TTA. But its nothing at all like SCCA classes/categories. Its.. "simpler"... you just find your base class, add up points for every mod you've done, and figure out where the car goes.

So to start the classing process, we have to know where we begin. Each car is assigned a "base classing", some with penalty points already assessed, and then you can count the additional "points" for any modifications done. Each class has 19 points worth of mods you can do, then you bump up to the next class at +20, and if you keep adding points you might go to the one past it. There's a set power-to-weight ratio limit within each class, and all sorts of modifiers for the power-to-weight number, too. Once you bump out of TTA you go up into the TTS>TTU>TTR classes, which do away with all of the "points" and are strictly power-to-weight ratio based classes. Clear yet?

Let's start out with the base classing for the "S197" chassis (2005-2012+) Mustang GT:

• '05-06 Mustang GT is TTD**
• '07-10 GT is TTC
• '11 GT is TTB

The two asterisks after the TTD class above means the '05-06 GT starts out in TTD class but begins its tally with +14 penalty points (each asterisk are worth +7), so that car can only do +5 worth of mods before going up to TTC.

So the 2011 GT with the new 412hp 5.0L got bumped up a full class from the 2010 GT, and the minimum race weight jumped dramatically to 3770 lbs (with driver). That series of base classing changes, to me, seemed to coincide with the power and suspension updates that the Shelby GT350 had for '07-08, which was an optional package those years. So the full class bump (a huge change) for the '11 GT had to include the power + the Brembo brakes, right?

Wrong. I got the bad news on the NASA forums today about more points assigned to our Mustang. This little tid-bit isn't even in the class rules, but is noted at the bottom of an online form for TTA-TTF classing:

Proceed to calculate your vehicle’s modification points assessment for up-classing purposes. Fill in the blanks with the number of modification points assessed for each item that affects your vehicle. You may leave the lines blank next to modifications that your vehicle does not have. Proceed to Page 2, and calculate all modification points’ assessments, then fill in total points below. ALL Factory Options and Parts Not on the Base Trim Model Must Be Assessed Points!!!

Somehow after 4 years of NASA TT racing I had missed this little note on the classification form about "factory options". This means that the following factory installed but optional bits on my 2011 GT will be assessed "points" for NASA classing - even if they are just cosmetic changes.


Left: The optional Brembo brakes are +2 points. Right: This front grill insert is is +3 points

Factory installed options, not on the "base trim level model", that will now count for mod points

• Rear wing delete = +4
• The optional 4-pedestal factory GT rear wing = +4
• A 71" wide multi-piece CF wing with a huge cord, up to 8" above the hoodline, and 12" tall end plates = also +4?!
• Brembo brake package = +2
• GT500 rear valance (now optional on all GTs) = +1 (planned)
• CS/GT front lower grill insert (now optional on all GTs) = +3 (planned)
• Boss302 LS front splitter = +6 (with the CS grill insert included)

Left: This is the base GT rear "wing". Zero points. Right: Ordering without that is +4!

Here's our current list of what I consider "real modifications:

• 265/40/18 Yokohama AD08 = +2 (for 140-200 treadwear)
• AST 4100s = +3
• Coilover Springs = +2
• Camber plates = +0

But we have many more mods planned, which was pushing us to the limit of TTB. Now add in the cosmetic changes we had planned and we're going to be well into TTA. This new twist is pretty crazy, and I'm pretty disgusted with the NASA TT rules at the moment, but that's the way it is written. Now every time I hear a NASA racer make fun of the SCCA's thick rulebook, I can point out how retarded it is that a factory optional wing delete counts the same number of points as a massive CF race wing.

All of these planned mods are legal for STX class, plus many more - and that class is essentially the slowest of all Street Touring classes (ie: STX cars still get beat by '89 civics with 100 hp). Doing some basic shocks + springs + these "factory option" mods above would kick the car up into TTA... which is home to C5 Z06 Corvettes on Hoosiers, and highly modified cars like supercharged Miatas with giant aero, at least here in Texas. So now at least we know all we need to account for to stay within TTB, right? Oh no, there's more.

There's the set power-to-weight ratio limit for TTB that we have to stay under

• Minimum Competition Weight for 2011 Mustang GT: 3770lbs with driver
• Tested Wheel Horsepower: 367 whp (corrected) It tested 378 uncorrected, but that doesn't matter. It was a chilly day.
• TTB Min Weight/Power Ratio: 10.25 lbs/hp

The Mustang currently weighs 3563 lbs, with zero fuel. Add +200 pounds for me and +50 pounds for fuel, and its around 3813 lbs. That gives me 372 whp before it would have to go up to TTA. Are we done yet? Nope.

Then there's the adjustment factors... see Appendix C (page 52-54)

• For running a smaller tire 275-250 mm DOT = +.4
• For having a competition weight 3800-3899 lbs = +.65
• Total adjustments = -1.05 (they show + when they mean -, but their example calculations show it correctly)
• 10.25 lbs/hp - 1.05 = 9.2 adjusted lbs/hp ratio.
• At 3813 lbs / 9.2 = 414 whp max for TTB for this car

And I assure you, someone will contend something in all of those calculations and rule interpretations in this post. "Its so easy" that it takes spreadsheets and multiple interpretations of rules to even class a car in TT. So now I see why the SCCA ruleset is made by a committee and is very carefully worded. There's less room for interpretation and the try to close these odd loopholes where a giant wind tunnel tested wing counts the same as a stock rear spoiler, or no wing at all. I have a new respect for the SEB today, after seeing this mess. You won't hear me singing their praises often, either.

So we've got some thinking to do. Every single mod we have planned has to be assessed for STX legality, NASA TT points, and if anything lowers the weight or ups the horsepower at all, we have to re-check the power to weight ratios. We know its unlikely that the 3800 pound race weight RWD Mustang is going to burn up the STX class, but TTA? We'd get killed on little 265mm street tires against typical TTA cars. Sure, going to TTA would give us another +19 in mods before we'd kick up to TTS, so we could go to a wider wheel and tire package, like go to giant Hooisers, just for TT use. Two sets of race wheels/tires, one of which is a gumball Hoo$iers? Then we could run a "Real Wing" for NASA and different aero bits for STX. And on and on...

The slippery slope begins. Fun, fun!



I was talking with Stuart from AST-USA today, who has an '06 GT (above, left), and his car starts at TTD** (as does Kent's shown above, right) so he could do a HUGE amount of suspension/wheel/Hoosiers/aero mods to his '06 and still stay in TTC class, whereas I've got to be really careful or my car bumps into TTA - even on street tires. So check your base classing, read the rules, and have the TT director check your classing form. And still, just be ready to have someone to contest it. One of our customers had a car that set some TT track records... never had a competitor protest, until a NASA director saw it and assessed something like +12 points to the front bumper, which was an aftermarket but purely cosmetic piece. All of his records and results were expunged. So sometimes, you never know where you should be classed with NASA.

Sorry to piss and moan so much in this "update", I'm just really frustrated with the TT rules and classing at the moment. I'm seriously looking at other cars to run in TT this year, like the E30 V8 or the E36 M3. The '11 Mustang GT is pretty much boned beyond what we've done now, and this is hardly the final set of mods we had planned for the car.

Cheers,

[Fair]

Originally Posted by modmustang97gt While it is nice to switch to the stock parts to avoid the points. It doesn't seem all that fair or encouraging that if I remove a spoiler and upgrade my brakes from stock to cobra pieces. I now have the same point assessment as someone with a G Stream rear wing and baer 6-pot brakes. Yet, the point assessment is the same.

Exactly my point...

Originally Posted by modmustang97gt The problem with rule sets is that vagueness seems like its encouraging until someone really figures it out. Everyone runs what they brung until someone shows up with their brilliant flavor of the week, and now no one is having fun. This is why spec classes are so popular. Its the price you pay I guess for a proper attempt at equality.

Well, its a pretty half-hearted attempt at "equality", in my view, when no rear cosmetic spoiler = huge CF wing. The whole note about "optional parts not on the base trim car have to take points" isn't even in the NASA TT rules, its a note attached to some online form. Seriously.

NASA TT is unique in that it has one person is making all of the base classing, modification point assessments, and rules, so we naturally get rules made from one person's point of view only. I wasn't the only one in the dark about this, so I (and others) have been trying to point out the absurdity of a factory spoiler delete having the same points as a full on race wing, over on the NASA Forum thread where this was pointed out to me. The Nat'l TT Director responded with this:

Originally Posted by Greg G. How about this---a driver takes off the OEM wing for the higher speed tracks that have less turns requiring rear downforce and more gain from less drag, and puts it back on for other tracks where the wing results in better lap times due to the need for more rear downforce. There is clearly a performance gain by doing this "modification". The amount of that gain would/could be different for each of the 800+ different car models possibly competing. So, we are back to "If the modification costs more points for your particular vehicle than it is worth, then don't do the Mod."

And my reply:

I get that, and I'm now not saying that removing an OEM style wing should be free... but +4 points? Its the severity of this penalty that sticks in my craw. Let's look at an example: The race wing shown above (G-Stream CF) as used on the Boss 302S race cars are +4 points, is adjustable, and produces real downforce. It can be even bigger for the same points in TT: as wide as the car (71"), up to 8" above the roofline, and limited to 12" tall end plates. No chord length limits. So a giant CF race wing is the same points penalty as removing a cosmetic OEM wing? That's my point. Almost every OEM wing ever produced is not producing much down force, and is built for styling/cosmetic reasons. Even the "big" wings on STis and EVOs produce very little down force. One of the few cars that had an adjustable, down force producing wing were some adjustable units used on Porsche GT3s. If there was a slight tweak to the wing rule, maybe stating... "Any OEM wing (or exact replica) made for the same model series/chassis can be used, or none at all, for +1. Any OEM wing that has adjustable angle of attack is +4" Just a thought.

Figured I'd share that here, just to show everyone where I'm coming from (and I've had a lot of PMs, along the same lines). So with all of these points for OEM options on our car, its clear to me that staying in TTB with any 2011 GT that isn't ordered at the most basic, Spartan trim level - with no zero cost options whatsoever - is almost an impossibility. I've counted over 12 points worth of TT mod points that my car could have just with OEM options. So I'm going to say "to Hell with it" and just do the mods that are legal in SCCA STX class and "run whatever TT class it falls into", like I had originally planned.

To that end, today I ordered a bunch of parts that will hopefully add something to the car (with respect to aero) for NASA or SCCA use. First was the (optional on the 2011 GT) CS lower valance (+3), then a 2011 GT "optional" 4-pedestal OEM rear wing (for STX use only, and totally legal there), and an APR Performance GTC-300 wing (67" wide, 3D airfoil shape) for TT use. Plus some other bits I'll show later - but I did not get the (now optional on the 2011 GT) lower rear GT500 valance, as it wasn't worth the cost ($270 shipped) or NASA points, and did nothing for performance (it was purely cosmetic). For the GTC300 wing we'll make the uprights and endplates to fit the TT rules, and use it only for TT. Since I'm already taking 4 freagin points for "no wing" I'm going to have a real wing, by Damn!


Left: The 2011 "base trim" GT lower front valance. Right: The 2011 optional "CS" lower front valance

The CS valance above ($240, shipped) should be here by Friday morning, so we'll get the front end pulled off and ready, and have it installed before we load the car into the trailer and head down to Houston for the NASA event his weekend at MSR-H. We've still got points to spare within TTB, at least for a little while longer (we don't even have swaybars or any exhaust work on the car yet), so that +3 won't hurt us much right now, and we can't do a splitter (again, for TT) on the front w/o this flat bottomed CS lower valance.

Sorry for all of the complaining and moaning about NASA rules - they are what they are, and the situation won't change anytime soon, so - oh well. I'll just go out there and try to have fun, and see where the car's at for now. I've never even run at MSR-H, so I don't have much hope for matching the TTB track record there (1:42.675, set by an BMW E46 M3 in Jan-09). Even with all of this drama, I'm still pumped to get back onto a dry track - its been too many months.

We now have all new NASA regional leadership in Texas, and they seem like really nice folks (from the Rocky Mountain region), so hopefully the event will run more timely than in the past - that's the plan, at least. They've already added more event dates for the Texas region (8 so far), which is up from the previous 6 we used to have. And hopefully my HPDE students won't kill me on track, ha.

Doing some final track prep on the Mustang today and tomorrow. I just picked up the trailer, AJ already reset the Mustang's front alignment, and I'm about to go out and slap on the class numbers & letters. Tomorrow we need to mount the two transponders and the CS valance on Friday morning - if it shows up in time. I'll post up with times, pics and such after the event, on Monday.

Getting close!

[Fair]

Project Update for Jan 27, 2011: Well, just wrapping up prep for the first "real" track event of 2011. Got some funny news last night - apparently our 2011 GT is contagious. An old friend/racing buddy Paul M drove our car once... that's all it took. He tried to order a car earlier this week, and we had his build all worked up on the computer: Brembo package, CS lower valance, GT500 rear valance, the 4-pedestal wing, 401A interior, Kona blue, SAT/NAV - all of the optional performance, functional, and cosmetic bits he wanted that aren't too tacky.

Then he saw this NASA "OEM options adds points" silliness...



So instead of getting the car he wanted, he found a car that fit NASA TT better. The car he bought was equipped with the "base" trim level GT wing (saves 4 points), base front and rear lower valances (saves 4 more), but still had Brembos (+2), had the NAV/SAT/Sync (I cannot overemphasize how AMAZING this system works), and was at least the color he wanted (and gorgeous). Its got the 400A leather interior, not the 401A kit like he wanted (different materials/dash), as well as the HIDs - but it was close as he could get. With this car he's now only starting with +2 points for NASA in TTB, instead of +10 like he would have been with all of the (cosmetic) options he wanted. Lesson learned. (more pics)

Anyway, Paul's car is still bone stock and looks pretty TALL parked next to mine... Attack of Godzilla!



It looked even more exaggerated in person. We measured the height differences back at the shop, and it was 2.0" in front and 2.25" in back, at the same points on the body. Some of its in the the coilovers, the rest is in the tire height differences (265/40/18 vs. 255/40/19 = 1" shorter tire, so 1/2" lower CG). The overall effect, visually, is huge. Our car isn't "Stanced-out" or anything, and you can't argue that a lower CG isn't better for grip and aero.


Left: Old and busted. Right: New hotness

Paul already has a SMod Subaru GC project underway, which will be his dedicated autox/TT car when it gets done (someday!), but for now the Mustang will step in and hold him over for track use + make for a fun street car. He traded in his '08 Subaru STi (TTA prepped) yesterday for this Mustang, which was probably a good idea seeing how much warranty work the Subie needed under his heavy right foot (engine problems - it go boom). We'll really see how strong the Coyote 5.0 and Getrag MT-80 are with Paul driving them, heh.



Anyway, Paul is building this car up a bit differently than mine, as Solo use and SCCA classing is not a concern for this one. He will instead focus on NASA TT use and build it to the limit of TTB... with no SCCA rules and autox compromises to limit it for TT use. But its still his primary street car, so its not a full-out track-only build, by any means. This will probably be closer to what a lot of you out there might do a 2011 GT, really.

We're going to first swap in some Eibachs springs (+2), Vorshlag plates (+0), and get lowered down by 1.5" next week - just for openers. ASTs will go on soon enough, but it will likely be using the new bits we're working on with AST. Then he's going to sit back and watch my car's on-track performance, and then see how the new aero bits and exhaust system planned work out, before moving much further into more mods. Should be a fun street car. Welcome to the Dark Side, Paul!



Just a few pics of installing the NASA TT required numbers (10") and class letters (4") on my car, before we load it onto the trailer tomorrow. NASA Texas is cracking down on number requirements in TT this year, and stated "no more taped numbers!", which is fine by me. Its hard to tell much about the car your passing (or being passed by) when they don't have proper numbers/class letters. This decal set-up shows class and number on the front, rear and sides, as well as SCCA classing on the sides (we're adding the required NASA decals at the track, plus a shout-out to GRM with their decals). Its just a temporary decal set-up, as we have our own vinyl plotter coming soon - so expect a more wild, completely tasteless graphic set-up soon.

NOTE: If anyone out there is a good graphic designer and can help us come up with new and unique Vorshlag livery for this car (that scales up to others car models - like our E30 & E46, plus some tester/customer cars), please PM me. Since we're getting a plotter we can try more stuff without racking up hundreds of dollars in vinyl bills anymore, until we get the look perfectly tasteless.

Thanks,

[Fair]

Project Update for Feb 3, 2011: A little late, but here's the report from the track event last weekend (NASA @ MSR-Houston, Jan 29-30).

Pictures: http://vorshlag.smugmug.com/Racing-E...ouston-012911/



On Friday morning we mounted two AMB transponders to the car: one wired transponder was registered for me in TTB as #193, and a second wireless transponder for Amy was entered as TTB #93, mounted straight to the front grill. The battery powered AMB mounted to the grill had a straight shot down to the ground, with no metal in its path. The wired unit was mounted to the inner fender, behind the strut on the RF corner, and also has a straight shot at the ground. We made an aluminum panel for the lighted switch panel that worked nicely.

AJ loaded up the car into the trailer Friday and Amy and I left at 3 pm; we made it from Dallas to MSR-Houston in about 5 hours, at a hair under 300 miles for the tow, of course with some traffic in downtown Houston. Somehow we managed to snag a good pit spot, in the dark, then unhooked the trailer and unloaded the car, and took it through tech at 8:30 pm Friday night. We got a logbook for the car and met a few NASA people while waiting in line, several of which mentioned reading this thread build-up. Reloaded the car in the trailer than went to find our hotel (luckily nearby - the race site is fairly remote).



Next morning at dawn we finally got to see the facilities at MSR-Houston, and they were pretty impressive. Lots of buildings, nicely paved parking pit areas, a concessions stand, several buildings of garages, Sunoco fuel pumps, and even an active kart track that was running all day Saturday. The weather was a bit chilly off and on, but not bad, with overcast skies most of the day. We had our drivers meeting for TT and then another for instructors, and I was assigned an HPDE2 student. He didn't have a passengers seat (CMC2 race car) but he already knew the track well, and pointed out some areas to me to watch out for, since I'd never seen the track. Other than checking in with him all weekend, and keeping an eye on him when I was riding through with other students, there wasn't much for me to do there. This let me work with Amy directly most of the weekend.

The Time Trial group was merged with HPDE4 for the weekend, which made for a 27 car session (24 TT drivers). Ken O had his very well prepped TTB E46 M3 out on Friday testing, so he was very quick in Saturday's TT session one, running a 1:44.049 on Hoosier R6s, which was faster than all other TT cars except one (and his fastest time of the weekend). We only got 4 timed laps that session, due to session scheduling catch-up (the NASA folks did a great job of keeping the event on schedule), and the best I could get in traffic was a 1:58.907 (11th fastest). Since I was an instructor I was able to take Amy out and let her see the track while I ran that session, which let her see the track before she drove it.



Amy took the Mustang out in HPDE3 all day, but their small run group (about 8 cars) was combined with HPDE 1 & 2, just for the first HPDE session. This was a mess, as a very slow going HPDE1 student held up the entire field for the whole session, with 17 cars trailing in a train at parade lap speeds. This was because they forgot how to give a point by - and so did his instructor (we brought this up at the instructor meeting shortly afterward). We even came into the pits, waited, went back out, and still caught the train in 2 corners. Wasted session, but by session 2 they had HPDE3 all on its own, and Amy had clean laps the rest of the day.


Video of me driving in Session 2 - click to view

After the first session, T&S had times for everyone in TT so they were able to grid us up in order of lap times (fastest first, slowest last), which made it easier to get cleaner track time - well, as much as you can get with 27 cars in the session. It helped a little, and I managed to knock off over 7 seconds to a 1:51.199 in session 2, and managed a 1:50.503 in session 3. I was still 6 seconds behind the TTB leader Ken O, which is an eternity. Without real tires I suspect the car always will be. There were several other 2011 GTs out there, but all of them were in TTA running on Hoosiers or Continental Challenge slicks, and one of them was pretty damn quick at a 1:44.502 (TTA #50, shown below)



I was gaining less time per session, but I was still learning the track and getting the tires and shocks dialed in. The Radical that was holding me up a bit in the session 2 video found some serious speed in session 3 so he was ahead of me on the grid for session 4 (and considerably faster on track). Since he wasn't getting quicker times, Ken O switched to his Dunlop Star Specs for this session, so I gridded up behind him. I got some clear track time but Ken slowly pulled away from me this session. His best time on his street tires was 1:48.314, and I managed to meet my goal of "running in the 1:49s" by ticking off a 1:49.999 on lap 7, my last hot lap of the day. So Ken was still a solid 1.7 sec quicker in the M3 on similar tires in the same session, but at least it was no longer 6 seconds, which didn't completely crush my ego. For Ken on that day, his 275/35/18 Hoosier R6s were worth 4.3 seconds per lap. That's a huge chunk of time for one mod, but that's why its +11 points for his TT classing.



continued below

[Fair]

continued from above

TTB was around 8 cars, and I was still 2nd quickest in class for the first 3 sessions, but that black Exige might have slipped past my best time in session 4 Saturday? Its hard to tell where I ended up, because the online event results that NASA uses (MyLaps) do not show class, car, or anything other than the driver's name, number, and lap time. These are without a doubt the worst online event results I've ever seen for any competitive event I've entered in the past 23 years. I mention this because at the event you could go up to T&S and beg for a copy of the printed results after each session, and these results showed the class and (sometimes) the car listed. For some reason this data just doesn't make it to into the MyLaps listings. Seriously - look at these EOD results for TT for Saturday and tell me who won what class: http://www.mylaps.com/results/showrun.jsp?id=1778791. You need a secret decoder ring (a printout from the event) to figure out who is in what class, and what car they were in. Event results should stand on their own, always. Other than this complaint, in my eyes the NASA folks did an excellent job, and kept the event on schedule, even with lots of racers pulling some on track shenanigans.

Amy improved throughout the day Saturday during her four HPDE sessions, and I pushed her in the 2 sessions I rode through with her and instructed. She got down into the 1:55 range with my hand timed laps, as MyLaps only captured her times on Sunday when she ran TT (HPDE isn't supposed to be timed). She was nailing every heel-toe downshift like a pro, and only lacked a bit of confidence to get into the gas sooner. I was using the Costas method of yelling "Gas! Gas! Gas!" at every corner exit, and pretty soon she had it down. Still, staying in the throttle all the way to at the end of the long straights (into Turns T13, T6 and T2) were the only things holding her lap times back. As she gets more comfortable in TT I'm sure she'll be right on my times, like she is in autocross.



Saturday night the NASA folks had a great party at the track, with a nice meal and cold beer, and the 2010 Texas Region Class Winners were announced. We got some good rest that night and made it back out Sunday morning, to the beginnings of a rainy day. For Sunday's first TT Session, Amy ran the car in TT (her first official TT session) and I rode along. It was starting to spit rain, and times in TT were markedly slower. Ken O was quickest, running a 2:12.574 on the Hoosiers, and Amy was 10th quickest at a 2:24.551. After that session it really started to rain and the track started to get slicker than snot.

I ran session 2 of TT in a downpour and only got a 2:27.572, which was 3rd quickest in the session. I did have a slight issue at the exit of turn 17, after making a pass coming in to this turn. I got a last second point-by from a slower car (otherwise I would have waited to pass) and braked deep into T17 over a patch of standing water, where I managed to put the car into a slide that... ahh.... turned into a gentle 360°. I stayed on track and never lost momentum (slid it in 1st gear when the car was backwards, and slipped out the clutch and back into throttle when the car was pointed back straight - the car never stopped moving forward on track), but this is technically called a spin, and a spin or an off gives any TT driver a DQ for that session. At least I gave the crowd something fun to watch in this session, heh.



Since we aren't planning on staying in TTB in this car too long (and therefore don't need to try to bank points for a shot at an annual NASA regional class win - not that anyone is going to beat Ken O again this year), and we both felt like we wrung out the times we were going to get back on Saturday, we loaded up the car for the trip home later that day. Soaked to the bone, and dead tired. This means I got no official session time for Sunday, of well. The rain didn't let up for hours, but I stuck around to help with instructing and we watched the Spec Miata/Spec 944 race and then the CMC/AI race, both of which were entertaining in the rain!



In Sunday's HPDE session 3 I was assigned a new student, an HPDE2 entrant, who wanted some tips for running in the wet. He was trying to move up though HPDE ranks so he could hopefully get his Comp license later this year (he's building a Spec 944 race car), and we worked on some rain driving techniques. He was an autocrosser and had some track experience in Germany at the 'Ring. He picked up on my rain driving tips quickly, and I signed him off to HPDE3 with permission of the Chief Instructor.

After session 3 the sky looked as bad as ever, and the crowd was thinning out considerably, so we headed back to Dallas and made it back in 4h 45m, driving through some rain and a hail storm (?!) at one point. Apparently it dried up at the track considerably for the 4th session, and the TT guys all went much quicker, which changed up the results considerably for Sunday. Again, if you can make any sense of these results, you're a better man than me: http://www.mylaps.com/results/showrun.jsp?id=1778792



So that was our first "real" competition track event in the Mustang. We had a blast and really enjoyed the event, even with the rain on Sunday and the utter trouncing we took in TTB at the hands of Ken O (he's a Vorshlag/AST tester, so its all good. Congrats on setting the TTB track record!). Hope this post wasn't too wordy and boring. Since its getting a bit long, I'll post some specific observations about the car in another post to follow.

Thanks,