Go Back   Dallas Fort Worth 5.0 Mustang Club > Photos & Videos > Foxbody 5.0s

Foxbody 5.0s For the original 5.0s that started it all


Sponsored Ads
Welcome to DFW50s.com

Register to remove these ads.




Reply
 
Thread Tools Display Modes
Old 05-15-2013, 01:31 AM   #1
OG Fox
Supporting Member
 
OG Fox's Avatar
 
Join Date: Jun 2012
Age: 40
Posts: 915
Default Header Install Tips and Tricks??

Looking on finally tackling the header install on the 82. I have some BBK 1 5/8 ceramic headers that im wanting to put on the car. I also want to get rid of all the smog bullshit on the car itself too.

So I will be ordering a pully to replace the smog as seen here.
pulley

and also need an air cleaner to replace the factory one.
air cleaner

then I know I will need a double hump transmission crossmember
here

Other than that, for those guys who have swapped headers on to a fox before. any other things i might need? im also open to tips/tricks. thanks a bunch guys.
OG Fox is offline   Reply With Quote
Old 05-15-2013, 05:08 AM   #2
Luke
Senior Member
 
Luke's Avatar
 
Join Date: Sep 2012
Location: Saginaw
Age: 38
Posts: 903
Default

No tips on the headers but while you're under there you might as well replace the starter if you have that old whiney one.
Luke is offline   Reply With Quote
Old 05-15-2013, 10:31 AM   #3
STROKD
Old School
 
Join Date: Oct 2012
Age: 46
Posts: 1,358
Default

Id buy ARP 3/8" header bolts... chrome (polished) or black, your choice. I like the chrome ones myself. Also Id use a Fel Pro header gasket. tighten the piss out of them, and when its running, drive it 50-100 miles, and retighten all of the bolts as tight as you can get. you should be all set after that. Sometimes people put a drop of blue locktite on the bolts to make sure they dont back out, Ive only done that on one car cause the motor shook so bad it rattled my bolts out. Id lose one once a week or so.
__________________
86 GT 374 Billet "W" w/ 72MMs
90 GT 351 Dart short stroke w/ YSi
STROKD is offline   Reply With Quote
Old 05-15-2013, 03:37 PM   #4
OG Fox
Supporting Member
 
OG Fox's Avatar
 
Join Date: Jun 2012
Age: 40
Posts: 915
Default

Originally Posted by STROKD View Post
Id buy ARP 3/8" header bolts... chrome (polished) or black, your choice. I like the chrome ones myself. Also Id use a Fel Pro header gasket. tighten the piss out of them, and when its running, drive it 50-100 miles, and retighten all of the bolts as tight as you can get. you should be all set after that. Sometimes people put a drop of blue locktite on the bolts to make sure they dont back out, Ive only done that on one car cause the motor shook so bad it rattled my bolts out. Id lose one once a week or so.
ok awesome tip. will do!
OG Fox is offline   Reply With Quote
Old 05-15-2013, 08:58 PM   #5
Toby
Senior Member
 
Join Date: Aug 2012
Age: 37
Posts: 459
Default

dont waste your money on the smog pulley, just re route the belt and get a shorter one. Go around the alternator, under the tensioner, around the ac, around the ps, over the water pump, then around the crank and back up to the alternator. headers are a piece of cake, I would highly suggest getting a set of percy aluminum header gaskets. I have literally reused mine 10+ times and they still seal with 0 issues.
Toby is offline   Reply With Quote
Old 05-15-2013, 09:31 PM   #6
Austin@BA-Speed
DFW5.0s Preferred Vendor
 
Austin@BA-Speed's Avatar
 
Join Date: Jan 2013
Location: NRH
Posts: 141
Default

+1 on aluminum header gaskets
__________________
'66 Ford Fairlane - '69 SCJ Mach 1 - '03 SB Cobra
Austin@BA-Speed is offline   Reply With Quote
Old 05-16-2013, 08:29 AM   #7
downtime!
Senior Member
 
downtime!'s Avatar
 
Join Date: Jun 2012
Location: Keller
Age: 61
Posts: 1,006
Default

Another vote for the shorter belt and no pulley. Tons easier and really cleans it up under there.
__________________
downtime! is offline   Reply With Quote
Old 05-16-2013, 01:49 PM   #8
OG Fox
Supporting Member
 
OG Fox's Avatar
 
Join Date: Jun 2012
Age: 40
Posts: 915
Default

Originally Posted by downtime! View Post
Another vote for the shorter belt and no pulley. Tons easier and really cleans it up under there.
ok might go this route to save some dough.
OG Fox is offline   Reply With Quote
Old 05-16-2013, 06:12 PM   #9
STROKD
Old School
 
Join Date: Oct 2012
Age: 46
Posts: 1,358
Default

dont really need the fake pulley bracket unless you have a blower kit that necessates it for belt clearance. the short belt works great, just make sure to remove the smog pump from the car or it will lock up on you if its not turning.
__________________
86 GT 374 Billet "W" w/ 72MMs
90 GT 351 Dart short stroke w/ YSi
STROKD is offline   Reply With Quote
Reply

Bookmarks




Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump