Go Back   Dallas Fort Worth 5.0 Mustang Club > 5.0 Mustang Forum > Suspension

Suspension Post up questions about your Mustang's suspension or ride quality


Sponsored Ads
Welcome to DFW50s.com

Register to remove these ads.




Reply
 
Thread Tools Display Modes
Old 07-08-2013, 08:38 AM   #1
Dominic Toretto
Senior Member
 
Dominic Toretto's Avatar
 
Join Date: Jun 2013
Location: Irving / Oklahoma City
Age: 41
Posts: 1,896
Default Control Arms

At what point should one consider switching to aftermarket control arms? I see a lot of aftermarket manufacturers producing upper and lower rear control arms for these cars. Since I am stock-piling parts right now, wasn't sure if this was something I should go ahead and get as well. Thanks guys.

-Alex
__________________
2012 GT Premium Hardtop with XX Transmission
Mods page: http://dfw50s.com/showthread.php?t=3376

Ford Racing . Pypes . BMR . CDC . American Muscle . DDM Tuning . BFG . J&M . Amsoil . MMD. JLT
Dominic Toretto is offline   Reply With Quote
Old 07-08-2013, 09:11 AM   #2
BlueBolt
Senior Member
 
Join Date: Oct 2012
Age: 37
Posts: 255
Default

If you have any wheel hop or are lowered any then yes get some control arms
BlueBolt is offline   Reply With Quote
Old 07-08-2013, 09:41 AM   #3
5PointSlow
Senior Member
 
5PointSlow's Avatar
 
Join Date: Oct 2012
Location: Mustang, Ok
Posts: 259
Default

I run the brembo/GT500 stock lowers with roush upper. No wheel hop issues and no NVH.
__________________
2015 Comp Orange GT Premium Perfomance Pack

SOLD!
2012 Kona Blue GT Premium
Roush TVS/JLT Big Air
Stainless Works Long Tubes and catted X.
Magnaflow Competition Catback
AED Tuned
***Driver Mod***
10.88@134 on street tires
5PointSlow is offline   Reply With Quote
Old 07-08-2013, 11:06 AM   #4
JDBishopArts
Senior Member
 
JDBishopArts's Avatar
 
Join Date: Aug 2012
Location: Valley Ranch
Age: 40
Posts: 1,123
Default

BMR makes a good product and Jason (Jayman) with Hypermotive Performance, one of our vendors has great deals and service on them.
JDBishopArts is offline   Reply With Quote
Old 07-08-2013, 11:33 AM   #5
Dominic Toretto
Senior Member
 
Dominic Toretto's Avatar
 
Join Date: Jun 2013
Location: Irving / Oklahoma City
Age: 41
Posts: 1,896
Default

What is NVH?

-Alex
__________________
2012 GT Premium Hardtop with XX Transmission
Mods page: http://dfw50s.com/showthread.php?t=3376

Ford Racing . Pypes . BMR . CDC . American Muscle . DDM Tuning . BFG . J&M . Amsoil . MMD. JLT
Dominic Toretto is offline   Reply With Quote
Old 07-08-2013, 12:10 PM   #6
DirtyD
Senior Member
 
Join Date: Jun 2012
Posts: 5,594
Default

Originally Posted by Dominic Toretto View Post
What is NVH?

-Alex
Noise Vibration and Harshness
DirtyD is offline   Reply With Quote
Old 07-24-2013, 09:04 AM   #7
Dominic Toretto
Senior Member
 
Dominic Toretto's Avatar
 
Join Date: Jun 2013
Location: Irving / Oklahoma City
Age: 41
Posts: 1,896
Default

Anyone considered using GT500 control arms? I would assume that they would be much stronger than the stock GT control arms and probably still able to argue them for warranty issues.

-Alex
__________________
2012 GT Premium Hardtop with XX Transmission
Mods page: http://dfw50s.com/showthread.php?t=3376

Ford Racing . Pypes . BMR . CDC . American Muscle . DDM Tuning . BFG . J&M . Amsoil . MMD. JLT
Dominic Toretto is offline   Reply With Quote
Old 07-24-2013, 09:30 AM   #8
jayman33
Senior Member
 
Join Date: Aug 2012
Posts: 428
Default

Dealerships would be hard pressed to void a warranty or determine the cause of an issue was due to using aftermarket LCA's.
Also, the GT500 LCA's are still stamped steel with rubber bushings. Deflection isn't necessarily bad in a suspension but too much is.
I spent the majority of my day yesterday grilling a race team on their suspension and they proved my theory right in regards to LCA's. BMR or Whiteline are the brands I would choose. I have Whiteline's LCA's on our 650HP GT, my Boss and our 800HP GT500 with zero issues and zero increased NVH. Both brands use a soft enough material to offer a little deflection but are hard enough to eliminate those typical issues found in street driving.
__________________

www.hypermotiveperformance.com
734-306-5231
jayman33 is offline   Reply With Quote
Old 07-24-2013, 09:47 AM   #9
Dominic Toretto
Senior Member
 
Dominic Toretto's Avatar
 
Join Date: Jun 2013
Location: Irving / Oklahoma City
Age: 41
Posts: 1,896
Default

Originally Posted by jayman33 View Post
Dealerships would be hard pressed to void a warranty or determine the cause of an issue was due to using aftermarket LCA's.
Also, the GT500 LCA's are still stamped steel with rubber bushings. Deflection isn't necessarily bad in a suspension but too much is.
I spent the majority of my day yesterday grilling a race team on their suspension and they proved my theory right in regards to LCA's. BMR or Whiteline are the brands I would choose. I have Whiteline's LCA's on our 650HP GT, my Boss and our 800HP GT500 with zero issues and zero increased NVH. Both brands use a soft enough material to offer a little deflection but are hard enough to eliminate those typical issues found in street driving.
Thank you for the informational and prompt response . Since the GT500s (Assuming regular GTs the manufacturing process) are stamped steel, what are the Whiteline and BMRs manufacturing process for these pieces?

-Alex
__________________
2012 GT Premium Hardtop with XX Transmission
Mods page: http://dfw50s.com/showthread.php?t=3376

Ford Racing . Pypes . BMR . CDC . American Muscle . DDM Tuning . BFG . J&M . Amsoil . MMD. JLT
Dominic Toretto is offline   Reply With Quote
Old 07-24-2013, 10:49 AM   #10
DirtyD
Senior Member
 
Join Date: Jun 2012
Posts: 5,594
Default

Originally Posted by Dominic Toretto View Post
Thank you for the informational and prompt response . Since the GT500s (Assuming regular GTs the manufacturing process) are stamped steel, what are the Whiteline and BMRs manufacturing process for these pieces?

-Alex
Tubular steel with penetration welds at each joint. I don't know if they are full penetration or not, though.


Sent from my iPhone using Tapatalk 2
DirtyD is offline   Reply With Quote
Old 07-24-2013, 03:12 PM   #11
jayman33
Senior Member
 
Join Date: Aug 2012
Posts: 428
Default

Correct, whiteline use 4130 chromoly with tig weld. BMR is mild steel with I beleive mig weld.
__________________

www.hypermotiveperformance.com
734-306-5231
jayman33 is offline   Reply With Quote
Old 07-24-2013, 08:52 PM   #12
emery2483
Senior Member
 
emery2483's Avatar
 
Join Date: Jun 2013
Location: Southlake
Posts: 105
Default

what do y'all think about the bbk lca?
emery2483 is offline   Reply With Quote
Old 07-24-2013, 10:26 PM   #13
jayman33
Senior Member
 
Join Date: Aug 2012
Posts: 428
Default

Dont know much about them
__________________

www.hypermotiveperformance.com
734-306-5231
jayman33 is offline   Reply With Quote
Old 07-24-2013, 10:48 PM   #14
Toby
Senior Member
 
Join Date: Aug 2012
Age: 37
Posts: 459
Default

You can't go wrong with bmr stuff. I have installed dozens of them with great fitment every time! also dont forget about the relocation brackets if you are lowered and plan to hit the track.

Give us a call at Truestreet, we are a dealer for BMR stuff, we can get you a great price on the parts with installation!
Toby is offline   Reply With Quote
Old 07-25-2013, 10:03 AM   #15
Luke
Senior Member
 
Luke's Avatar
 
Join Date: Sep 2012
Location: Saginaw
Age: 38
Posts: 903
Default

+1 for BMR!
Luke is offline   Reply With Quote
Reply

Bookmarks




Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump